do not scale from this print "a" "a" "b" "b" contact xwcx-xx-xx-xxx fig 1 "a" "b" ref section "a"-"a" scale 3 : 1 wire crimp ref "d" "c" section "b"-"b" scale 3 : 1 insulation crimp "a" "a" "b" "b" terminal xwcx-xx-xx-xxx "e" see table 4 overall length "f" see table 4 overall length "g" "e" "e" "e" see table 4 overall length "h" "e" (tab length) "h" max (burr allowance) "j" max fig. 3 (carrier tab specifcation) fig 2 in-process -s: single end -d: double end -t: transfer end cable cut in-process cut length is assembly length minus overall length subtractor * for crimp inspection callouts contact/terminal - lead style - crimp - awg - cable type see table 1 for example, if inspecting a crimp of c-179-02-x with 26awg dwc, the callout for inspection would be "c-179-02-crimp-26-dwc" table 5 cut cable depth/dimension bwc-01-04-01 0.55[14mm] bwc-01-16-01 1.34[34mm] bwc-02-10-01 0.71[18mm] bwc-02-32-01 1.18[30mm] bwc-05-14-01 0.31[18mm] uca-01-01 0.47[12mm] uca-02-01 0.55[14mm] uca-03-01 0.63[16mm] eca-01-01 0.79[19mm] eca-02-02 0.79[19mm] sctp-05-02 0.83[21mm] sctp-08-02 1.10[28mm] lspc-26100-05-p5-h 1.10[28mm] lspc-26100-08-h 1.26[32mm] lspc-26100-12-h 1.57[40mm] stcp-08-01 0.91[23mm] sctp-12-01 1.06[27mm] sctp-16-01 1.18[30mm] sctp-24-01 1.42[36mm] lspc-30100-05-p5-h 0.79[20mm] lspc-26100-09 1.18[30mm] lspc-26100-08-p5-h 1.18[30mm] lspc-26100-08 1.10[28mm] lspc-26100-12 1.26[32mm] sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] by: CRIMP-SPECIFICATIONS dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d.schmelz 10-11-2010 4 1 sheet scale: 1:0.571429 f:\dwg\misc\mktg\CRIMP-SPECIFICATIONS-mkt.slddrw notes: 1. represents a critical dimension. 2. all crimp and strip dimensions shown shall supercede any equivalent specifications that are supplied by tooling manufacturer. 3. for lengths less than 12 in, tolerance shall be +/-.125. for other lengths, tolerance shall be +/-2%. 4. maximum burr allowance: .003 [.08] 5. pull force must meet required table 1 specification for wire gauge being used. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 crimp/strip specifications revision ai
sheet of crimp/strip specifications by: CRIMP-SPECIFICATIONS dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d.schmelz 10-11-2010 4 2 sheet scale: 1.75:1 revision ai f:\dwg\misc\mktg\CRIMP-SPECIFICATIONS-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
sheet of crimp/strip specifications by: CRIMP-SPECIFICATIONS dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d.schmelz 10-11-2010 4 3 sheet scale: 1.75:1 revision ai f:\dwg\misc\mktg\CRIMP-SPECIFICATIONS-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
cat: crimp application tooling -ma: machine applicator -ht: hand tool -xxx: contact -xxxx: gauge range -xx: -tr(pre feed 30mm stroke) -fr (pre feed 40mm stroke *) -fs (post feed 40mm stroke) -xx: insulation thickness -01 (for 300v) -02 (for 600v) -03 (for teflon) * samtec production tooling standard sheet of crimp/strip specifications by: CRIMP-SPECIFICATIONS dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d.schmelz 10-11-2010 4 4 sheet scale: 1:0.571429 revision ai f:\dwg\misc\mktg\CRIMP-SPECIFICATIONS-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|